How to Apply Window Cling Without Bubbles or Wrinkles

What Should You Do Before the Cling Touches the Glass?

Clean the glass on the face where the cling will sit, and choose the mount before you order so the print is made to read the right way.

1. Wash that face of the glass and remove dust, tape gum, and any old film.
2. Wipe it with a cloth that does not shed fibers.
3. Confirm the cling matches the mount you chose when ordering: Inside Mount goes on the indoor face, Outside Mount on the outdoor face.
4. Mark the corners lightly with small pieces of painter's tape on the glass, then step outside and check that outline from the sidewalk.
5. Peel the backing only after that position looks right.

Inside Mount means the cling goes on the indoor face and is read from outside. Outside Mount means it goes on the outdoor face for a direct outdoor application. Both are the same price. The page defaults to Inside Mount. Change it if someone will apply the film from the sidewalk.

The product page does not list a temperature window or a cure time. As a general practice, apply when the glass is dry enough for the method you chose and when you can stand still and squeegee without rushing the edges.

How Do You Put the Cling on the Glass, Wet or Dry?

Press from the middle outward, whether you apply dry or with a light film of water. The product page does not name a size where wet application becomes required, so treat both as general practice and use the one that lets you place the piece straight.

Dry application:

1. Peel the backing.
2. Set one edge of the cling on the clean, dry glass.
3. Lay the rest of the film down without stretching it.
4. Press from the center and move toward the edges.
5. If a bubble stays, lift the nearest edge and lay that area down again.

Wet application, for a piece you want to slide into place:

1. Mist the clean glass with a light film of water.
2. Peel the backing and set the cling on the wet glass.
3. Slide it until the position matches the taped outline.
4. Press from the center outward so the water and air leave at the edges.
5. Wipe the glass around the cling after the film is down.

Once the film is flat and the edges are down, it is in place. If an edge lifts, lift it a little further, wipe the glass and the back of the cling clean, and smooth the edge down again.

Which listed size to order is a separate question. The window cling size guide matches door hours, windows, and full panes. This page is the application.

How Much Do the Listed Window Cling Sizes Cost?

A 24 x 36 inch static cling is $74.89, a 12 x 18 inch cling is $32.09, and a 48 x 72 inch cling is $267.49. Inside Mount and Outside Mount do not change these prices. Each figure is one piece.

The product page lists $10.65 per square foot. Use the piece prices in the table when you order a listed size. A small cling can price above a straight multiplication of that rate, so do not budget a 12 x 18 from the rate alone. Custom sizes are typed on the product page. The cost per square foot guide is the place for that rate in more detail.

Flat $10 ground shipping to any US address is added to the order. These clings are printed in the USA. Production is 48 hours after proof approval, before transit.

How Do You Remove a Window Cling and Store It for Reuse?

Peel the cling off, lay it back on its backing, and store it flat. Because there is no adhesive, a careful peel leaves the glass without residue.

1. Lift a corner with a fingernail or a plastic edge.
2. Peel the cling back on itself in a slow, even pull.
3. Lay it flat onto the backing it shipped on.
4. Store that sandwich flat, out of a rolled tube and away from a hot dashboard.

Reuse is often possible when the cling is stored that way. The product page says clings are suited to messages you rotate, such as seasonal promotions and changing hours. It does not promise a set number of removals. If the film is creased, stretched, or stored without the backing, the next application is less likely to lie flat.

When the glass needs a mark that stays for the year, switch products. A cling is the wrong tool for a permanent logo.

When Should You Choose a Decal Instead of a Cling?

Choose a decal when the graphic should stay, and a cling when you will take it down. A cling holds by static and comes off clean. Adhesive vinyl bonds to the glass and is the better fit for a logo, door lettering, or hours that will not change for a long stretch.

The window decal versus window cling guide compares those jobs. Many shops use both: adhesive lettering for the name, and a cling for the offer that ends. Do not put a cling on a textured wall or a painted panel and expect it to hold. This film is for glass.

If the pane should show a full-color picture and people inside still need to see out, that is perforated window film, not a solid cling. A cling covers the glass it sits on.

How Do Artwork, the Proof, and Production Work?

Production is 48 hours after the proof is approved, and shipping transit is extra. Inline Graphics sends the free digital proof after the order is placed. Nothing prints before that approval.

There is no production setup fee. Any file or image you already have goes through AI image to print for $14.99 per item, charged once per cart line however many identical copies you order, not per square foot. Design it for me is $29.99 and includes two revisions. It is free only when that item is $499 or more. Every listed size in the table above is under $499, so Design it for me is $29.99 on those pieces.

On the proof, check the size, the mount you selected, and that the words read the right way for the face you will apply. Catch a backward line before you approve, not after the film is on the glass.

Flat $10 ground shipping to any US address follows production. Add transit when you are timing a sale or a holiday hour change.

Need window clings or other custom printing? Inline Graphics helps businesses, churches, schools, and event organizers across the country design and print cards, banners, signs, decals, displays, and marketing materials that get noticed. Contact us today for a quote.